First time on hand
Vostok Watches 🇺🇦
Vostok Watches 🇺🇦
Starting a store for Vostoks/USSR-watches, what are some headaches existing ways of getting (vintage) watches give you?
Vostok Watches 🇺🇦
Need help identifying this one
Vostok Watches 🇺🇦
Just got this lot of Vostok/soviet watches at 6€/watch (they all work with some needing cleaning or spare parts)
Vostok Watches 🇺🇦
Just got this off eBay
A place for anything Swatch!
Is 50$ fair for these two watches?
Vostok Watches 🇺🇦
My first Raketa ordered today
Community for fans of Raketa watches old and new
Picked this up in Kyrgyzstan
Vostok Watches 🇺🇦
I got these watches for myself (1st) and my Georgian father in law (2nd), but cannot figure out the model of the first watch.
Vostok Watches 🇺🇦
Let’s make Austal LTD. the next $GME!
Like 4chan found a Bloomberg Terminal.
Doing an Internship in Macedonia, is there anything that is a must-see in Skopje, is there any things to avoid?
Macedonia on Reddit
Upgrading my Goldfish’s tank from 54l to 300l [need help with picking tankmates]
The subreddit for anything related to aquariums! Come here to enjoy pictures, videos, articles and discussion. We're also here to help you if you need advice.
Visiting 🇽🇰/Pristina in February. Is there anything I need to look out for/avoid? Do you have recommendations for sights/nightlife?
Explore Kosova's rich history, culture, sports, cities, and tourism all in one place.
Werde ich mit 1,9 bei Jura angenommen?
Welcome to r/LMUMunich, a community for everybody studying or interested in studying at Ludwig-Maximilians-Universität München.
Why are my Ember Tetras dying? I recently bought 5 of them as mates for my Amazon puffer, today two of them just died out of nowhere, they showed no bite marks or signs of illness, I immediately checked the water parameters but everything was fine. The other fish are showing no atypical behaivior.
The subreddit for anything related to aquariums! Come here to enjoy pictures, videos, articles and discussion. We're also here to help you if you need advice.
My Amazon Puffer is flaring at other fish (Otocinclus and Ancistrus catfish)since I added new tankmates, before I didn’t have any problems with other fish, he is ignoring his older tankmates (that were added some time ago). Is this temporary stress or will this be permanent behavior?
The subreddit for anything related to aquariums! Come here to enjoy pictures, videos, articles and discussion. We're also here to help you if you need advice.
What could be causing this? My slicer (Wanhao CW) always messes up my models dimensions and won’t go any wider then this.
/r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
Are there any valid informations about the current state of the Ukrainian navy out there?
A forum for combat footage, and photos, from historical to ongoing wars.
A little insight into my shipyard, all models are 100% printed in scale 1/100, the ships are the MN Bouvines (left) and HDMS Helgoland (right)
/r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
Just installed a new Hotend to my ANET E10, now it is smelling burnt when it heats up and starts smoking at 200 degrees, is this normal for a brand new Hotend?
/r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
Ramps Board just fried my Arduino the first time I put on, even though everything was plugged in correctly. (PSU and Stepper drivers were plugged in) Guess I‘ll have to get a new one.
/r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
Can anyone recommend the hangprinter? It seems like a cheap way to get a very large printer, but also like a pain to set up. I mainly print out ship models with 80cm to 150cm in lenght, so I could profit from a very large build volume like this.
/r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
Maybe out of place here, but here is my 3D printed model of the battleship Dingyuan in 1/100.
/r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
My 1/100 Ironclad Dingyuan (fully printed)
The subreddit dedicated to the hobby of plastic model kit building and painting. Swap tips and techniques, show your latest builds/WIPs, post kit reviews and discuss the latest kits! And much more!
My 1/100 versions of the Chinese battleship Dingyuan and multiple other ships are available on Cults now, all models were made with RC in mind and are printable.
A place for Cults3D users. Share your creations, prints and suggestions about one of the best 3D printable model sharing platforms!